1.移動式皮帶運輸機運轉作業前，應將行走輪用三角木對稱楔緊。固定式皮帶運輸機，應安裝在牢固的基礎上。
2.起動前，調整好辦減速這松緊度，帶扣應牢固，軸承、齒輪、鏈條等傳動部件應良好，托輪和防護裝置應齊全，電器接地(接零)保護良好，輸送帶與滾筒寬度應一致。
3.應先空載起動，待運轉正常后，方可均勻裝料，不得先裝料后起動。
4.作業中，應隨時注意機械的運轉情況如發現輸送帶有松馳或走偏現象，應停車進行調整或修理。嚴禁在運轉中進行修理和調整。
5.作業時，嚴禁任何人員從皮帶運輸機下面穿過或跨越輸送帶。輸送帶打滑時，不得用手抖動拉動。
6.輸送大塊物料時，輸送帶兩側應加裝檔板或柵欄等防護裝置。
7.運轉中需要停機時，應先停止裝料，待輸送帶上料卸盡后，方可停機。
8.遇電源突然中斷或其它原因突然停車，應立即切斷電源，然后將皮帶上的物料清除掉，等來電或排除故障后，再接通電源啟動運轉。
9.停車前必須先與有關方面聯系，待輸送帶上的物料完全卸掉后，方可停機。
10.停機后應切斷電源，鎖好電源開關箱，對機械各部進行保養。用防雨護罩將電動機蓋好。
中譯英：
1 mobile belt conveyor running before the work, should the walking wheel with wooden triangle symmetric wedge. Fixed belt conveyer, should be installed on a solid basis.
2 before starting, adjustment of the tightness of the easy reduction, buckle should be firm, bearing, gear, chain and other transmission parts should be good, the supporting wheel and the protective device should be complete, electrical grounding ( zero) to protect the good, the belt and the roller width should be consistent.
3 first no-load starting, to be in normal operation, can be uniformly charging, not to charge after starting.
4 work, should always pay attention to mechanical running condition such as found in conveyor with relaxation or off phenomenon, should stop adjustment or repair. Is strictly prohibited in the operation for repair and adjustment.
5 operations, and forbids any personnel from the belt conveyor below through or across the conveyor belt. The conveying belt, not to hand shake pulling.
6 conveyor bulk materials, two sides of the conveyer should install baffles or fence protective device.
7 operation need to stop, should stop charging, stay on the conveyor belt after discharge, before shutdown.
8 in the event of power supply is suddenly broken or other causes of sudden stop, should be immediately cut off the power supply, then the belt material removed, such as call or after troubleshooting, and then turn on the power supply to start running.
9 parking must be concerned with relation to the conveyor belt, the material is fully unloaded, before shutdown.
10 stops should be cut off the power supply, power lock switch box, the Department of mechanical maintenance. Rainproof cover for motor cover.
(圖/文www.changrong-jx.com)
|
VR全景
蘇公網安備 32020602000237號